Panel Furniture Equipment & Solution Specialist

Panel furniture machines, model by model

CNC beam saws, nesting lines, edge banders and six-sided drills from Shunde, Foshan — every model in our catalogue is shown here with its own photo, its detail photos and its full parameter table, so you can compare before you ask.

ZORIDA RKS-K8+9V CNC nesting line with automatic label printer, from the ZORIDA catalogue
RKS-K8+9V CNC nesting line with automatic label printer — catalogue photo.
48 modelsshown with photos & full parameters
3 core seriescutting & CNC · edge banding · drilling
Shunde, FoshanChina's furniture machinery base
Worldwideexport packing & container loading

The Catalogue

Three series, every model

The three core processes of a panel furniture factory, in the order a panel moves through the line — cutting, edge banding, then drilling. Open a series to compare its models one by one — photo, working units, detail photos, introduction and the complete parameter table from our catalogue for each one.

Series 01

Cutting & CNC Nesting Series

Six RCJ beam saws from 1500 to 4500 mm work width, two nesting lines and four RTS machining centres — in the catalogue’s own order. The saw and router cards carry their complete catalogue parameter tables; the two lines are specified station by station.

CNC video premieres 25 November

The full working video of our CNC nesting line premieres on the ZORIDA Machinery YouTube channel on 25 November. Subscribe there, or ask us on WhatsApp and we will send the video as soon as it is live.

There is no beam saw video yet — rather than show you a different machine, ask us and we will film the RCJ cutting panels for you.

Request a Working Video

CNC Beam Saws — RCJ Series

ZORIDA RCJ1500E CNC Panel Saw (Beam Saw) — catalogue photo, PDF p.2

CNC Panel Saw (Beam Saw)

RCJ1500E

The compact beam saw of the RCJ family, sized for a 1500 mm work width — the format for workshops cutting standard sheets across their short side, or working in smaller spaces.

  • 8 grippers, a 1 kW saw base drive and two air-float tables (1750 × 540 mm)
  • The only family member without a side alignment motor
  • Saw carriage moves automatically to the panel width, shortening travel on every cut
  • Main saw and scoring (groove) saw rise and fall independently for a clean, chip-free cut edge
  • Side alignment keeps small panels true — servo control optional
  • Industrial touch-screen control with cutting optimisation software and barcode printer
Work width
1500 mm
Work thickness
100 mm
Min. panel size (W×L)
5 × 40 mm
Main saw blade / shaft
Ø360–400 mm / Ø75 mm
Groove saw blade / shaft
Ø180 mm / Ø50 mm
Main saw motor
16.5 kW
Groove saw motor
2.2 kW
Saw base drive motor
1 kW
Side alignment motor
Not fitted
High-pressure blower motor
2.2 kW
Gripper quantity
8
Air-float table size
1750 × 540 mm (2 pcs)
Dust extraction
Ø100 × 4
ZORIDA RCJ2800E CNC Panel Saw (Beam Saw) — catalogue photo, PDF p.2

CNC Panel Saw (Beam Saw)

RCJ2800E

The 2800 mm model — the working width of the standard 9 × 6 ft sheet — for cabinet plants cutting full sheets as their daily work.

  • 11 grippers, a 0.55 kW side alignment motor and three air-float tables
  • Saw carriage moves automatically to the panel width, shortening travel on every cut
  • Main saw and scoring (groove) saw rise and fall independently for a clean, chip-free cut edge
  • High-precision grippers position the book so every part is cut on the same straight line
  • Side alignment keeps small panels true — servo control optional
  • Industrial touch-screen control with cutting optimisation software and barcode printer
  • Family details and the side push / side clamp options are shown below the RCJ cards
Work width
2800 mm
Work thickness
100 mm
Min. panel size (W×L)
5 × 40 mm
Main saw blade / shaft
Ø360–400 mm / Ø75 mm
Groove saw blade / shaft
Ø180 mm / Ø50 mm
Main saw motor
16.5 kW
Groove saw motor
2.2 kW
Saw base drive motor
1.8 kW
Side alignment motor
0.55 kW
High-pressure blower motor
4 kW
Gripper quantity
11
Air-float table size
1750 × 540 mm (3 pcs)
Dust extraction
Ø100 × 4
ZORIDA RCJ3300E CNC Panel Saw (Beam Saw) — catalogue photo, PDF p.2

CNC Panel Saw (Beam Saw)

RCJ3300E

The 3300 mm model — and the machine in the catalogue's main RCJ photograph; its badge is readable on the saw body.

  • 13 grippers hold the book across the wider span, with a 4 kW high-pressure blower
  • Three air-float tables (1750 × 540 mm) for moving full sheets
  • Saw carriage moves automatically to the panel width, shortening travel on every cut
  • Main saw and scoring (groove) saw rise and fall independently for a clean, chip-free cut edge
  • High-precision grippers position the book so every part is cut on the same straight line
  • Side alignment keeps small panels true — servo control optional
  • Industrial touch-screen control with cutting optimisation software and barcode printer
  • Family details and the side push / side clamp options are shown below the RCJ cards
Work width
3300 mm
Work thickness
100 mm
Min. panel size (W×L)
5 × 40 mm
Main saw blade / shaft
Ø360–400 mm / Ø75 mm
Groove saw blade / shaft
Ø180 mm / Ø50 mm
Main saw motor
16.5 kW
Groove saw motor
2.2 kW
Saw base drive motor
1.8 kW
Side alignment motor
0.55 kW
High-pressure blower motor
4 kW
Gripper quantity
13
Air-float table size
1750 × 540 mm (3 pcs)
Dust extraction
Ø100 × 4
ZORIDA RCJ3800E CNC Panel Saw (Beam Saw) — catalogue photo, PDF p.2

CNC Panel Saw (Beam Saw)

RCJ3800E

The first of the wide trio the catalogue groups under one photograph: 3800 mm work width for plants cutting jumbo sheets and wide books.

  • 14 grippers and a doubled high-pressure blower set (4 kW + 2.2 kW)
  • Four air-float tables for moving big books
  • Saw carriage moves automatically to the panel width, shortening travel on every cut
  • Main saw and scoring (groove) saw rise and fall independently for a clean, chip-free cut edge
  • High-precision grippers position the book so every part is cut on the same straight line
  • Side alignment keeps small panels true — servo control optional
  • Industrial touch-screen control with cutting optimisation software and barcode printer
  • Family details and the side push / side clamp options are shown below the RCJ cards
Work width
3800 mm
Work thickness
100 mm
Min. panel size (W×L)
5 × 40 mm
Main saw blade / shaft
Ø360–400 mm / Ø75 mm
Groove saw blade / shaft
Ø180 mm / Ø50 mm
Main saw motor
16.5 kW
Groove saw motor
2.2 kW
Saw base drive motor
1.8 kW
Side alignment motor
0.55 kW
High-pressure blower motor
4 kW + 2.2 kW
Gripper quantity
14
Air-float table size
1750 × 540 mm (4 pcs)
Dust extraction
Ø100 × 4
ZORIDA RCJ4200E CNC Panel Saw (Beam Saw) — catalogue photo, PDF p.2

CNC Panel Saw (Beam Saw)

RCJ4200E

The 4200 mm model of the wide group, for plants cutting jumbo sheets lengthwise or running wide books for wardrobe and door production.

  • 15 grippers, the doubled blower set (4 kW + 2.2 kW) and four air-float tables — as on the 3800E
  • Steps up from the 3800E in width and gripper count only; the saw unit and controls are the family's
  • Saw carriage moves automatically to the panel width, shortening travel on every cut
  • Main saw and scoring (groove) saw rise and fall independently for a clean, chip-free cut edge
  • Side alignment keeps small panels true — servo control optional
  • Industrial touch-screen control with cutting optimisation software and barcode printer
Work width
4200 mm
Work thickness
100 mm
Min. panel size (W×L)
5 × 40 mm
Main saw blade / shaft
Ø360–400 mm / Ø75 mm
Groove saw blade / shaft
Ø180 mm / Ø50 mm
Main saw motor
16.5 kW
Groove saw motor
2.2 kW
Saw base drive motor
1.8 kW
Side alignment motor
0.55 kW
High-pressure blower motor
4 kW + 2.2 kW
Gripper quantity
15
Air-float table size
1750 × 540 mm (4 pcs)
Dust extraction
Ø100 × 4
ZORIDA RCJ4500E CNC Panel Saw (Beam Saw) — catalogue photo, PDF p.2

CNC Panel Saw (Beam Saw)

RCJ4500E

The widest RCJ at 4500 mm, built to keep full-width books aligned through the cut on the longest sheets.

  • 17 grippers — the most in the family
  • Blower set and four air-float tables match the other wide models
  • Saw carriage moves automatically to the panel width, shortening travel on every cut
  • Main saw and scoring (groove) saw rise and fall independently for a clean, chip-free cut edge
  • Side alignment keeps small panels true — servo control optional
  • Industrial touch-screen control with cutting optimisation software and barcode printer
Work width
4500 mm
Work thickness
100 mm
Min. panel size (W×L)
5 × 40 mm
Main saw blade / shaft
Ø360–400 mm / Ø75 mm
Groove saw blade / shaft
Ø180 mm / Ø50 mm
Main saw motor
16.5 kW
Groove saw motor
2.2 kW
Saw base drive motor
1.8 kW
Side alignment motor
0.55 kW
High-pressure blower motor
4 kW + 2.2 kW
Gripper quantity
17
Air-float table size
1750 × 540 mm (4 pcs)
Dust extraction
Ø100 × 4

RCJ family — detail photos & options (catalogue p.2)

The catalogue shows these family details once, for all six RCJ models: the grippers, side alignment and industrial control touch screen fitted across the range, and the two framed options.

RCJ family — detail photos & options (catalogue p.2) — Grippers
Grippers
RCJ family — detail photos & options (catalogue p.2) — Side alignment
Side alignment
RCJ family — detail photos & options (catalogue p.2) — Industrial control touch screen
Industrial control touch screen
RCJ family — detail photos & options (catalogue p.2) — Option: Side push
Option: Side push
RCJ family — detail photos & options (catalogue p.2) — Option: Side clamp
Option: Side clamp

CNC Router Lines

ZORIDA RKS-K8+9V CNC Router Line (Nesting Line) — catalogue photo, PDF p.3

CNC Router Line (Nesting Line)

RKS-K8+9V

A full nesting line: sheets are loaded, labelled by the automatic label printer, nested and cut, then discharged — part labels are applied before cutting, as the catalogue's callout shows.

  • HQD 9 kW spindle with an 8-position round ATC
  • 9-drill vertical boring block (the +9V) for hinge and connector holes in the same cycle
  • Automatic label printer labels every part before it is cut (detail photo below)
  • Also built as the RKS-L12 (12 linear ATC, 9500 mm line, 3800 kg) and RKS-F4 (four 6 kW spindles, 9500 mm line) — tell us which configuration to quote
  • Drill head, saw blade, barcode printer and labelling are catalogue options across the line
  • Family specification details and options are shown below the RTS cards (catalogue p.5)
Working size
1300 × 2800 × 50 mm
Spindle
HQD 9 kW
ATC
8 round ATC
Control system
Weihong computer
Servo system
Weihong
VFD
Fulling 11 kW
Vacuum pump
Eurovac dry
Pump power
7.5 kW · 250 m³
Touch-off device
Yes
Travel speed X/Y
70 m/min
Travel speed Z
10 m/min
Working speed X/Y
20 m/min
Working speed Z
10 m/min
Total power
23 kW
Positioning cylinders
2 position strips
Dust outlet
Ø200 × 1 + Ø100 × 1
Overall size
13400 × 2300 × 2500 mm
Weight
4500 kg
ZORIDA RTS-12L CNC Nesting Line — catalogue photo, PDF p.3

CNC Nesting Line

RTS-12L

The second nesting line in the catalogue, shown with its four working stations: a load lift table presents the sheets, a vacuum loader places them, a pusher keeps them registered, and a belt output conveyor discharges the cut parts.

  • Four stations, each photographed on its catalogue page: load lift table, vacuum load, pusher, belt output conveyor
  • The router itself can be swapped: 1, 2 or 4 spindles, round ATC or linear ATC
  • Drill head, saw blade, barcode printer and labelling are catalogue options
  • The configurable line — we build the station list around your sheet format and daily volume
  • The catalogue presents this line by configuration rather than a fixed parameter column; the full data sheet is supplied with your quotation
Loading
Load lift table
Sheet loading
Vacuum load
Registration
Pusher
Outfeed
Belt output conveyor
Router options
1 / 2 / 4 spindles · round ATC · linear ATC
Options
Drill head · saw blade · barcode printer & labelling

The catalogue presents this line by configuration rather than a fixed parameter column; the full data sheet is supplied with your quotation.

CNC Routers — RTS Machining Centres

ZORIDA RTS-1S CNC Router (Machining Centre) — catalogue photo, PDF p.4

CNC Router (Machining Centre)

RTS-1S

The single-spindle machining centre: one HQD 6 kW spindle and no tool changer — the economical way into the RTS platform for shops nesting and cutting full sheets.

  • HQD 6 kW spindle, no ATC — tools are changed by hand
  • Leadshine simple servo control, where the rest of the family uses the Weihong computer system
  • The lightest (1800 kg) and lowest-powered (20 kW) of the range, with a smaller 5.5 kW / 160 m³ vacuum pump
  • Slower Z axis than its brothers: 8 m/min travel, 5 m/min working
  • Family specification details and options are shown below the RTS cards (catalogue p.5)
Working size
1300 × 2800 × 50 mm
Spindle
HQD 6 kW
ATC
Not fitted
Control system
Leadshine simple servo
Servo system
Weihong
VFD
Fulling 7.5 kW
Vacuum pump
Eurovac dry
Pump power
5.5 kW · 160 m³
Touch-off device
No
Travel speed X/Y
70 m/min
Travel speed Z
8 m/min
Working speed X/Y
20 m/min
Working speed Z
5 m/min
Total power
20 kW
Positioning cylinders
4 pcs
Dust outlet
Ø200 × 1
Overall size
4200 × 2300 × 2500 mm
Weight
1800 kg
ZORIDA RTS-L12 CNC Router (Machining Centre) — catalogue photo, PDF p.4

CNC Router (Machining Centre)

RTS-L12

The linear-ATC centre: twelve tools wait in a row at the back of the table — the catalogue's inset shows the 12-ATC-in-one-row rack — so complex parts with many tools finish in one cycle.

  • HQD 9 kW spindle served by the 12-position linear tool rack
  • For mixed work: cutting, drilling, grooving and profiling in a single nesting program
  • Weihong computer control and servo system
  • 7.5 kW Eurovac dry vacuum pump and touch-off device fitted
  • Family specification details and options are shown below the RTS cards (catalogue p.5)
Working size
1300 × 2800 × 50 mm
Spindle
HQD 9 kW
ATC
12 linear ATC
Control system
Weihong computer
Servo system
Weihong
VFD
Fulling 11 kW
Vacuum pump
Eurovac dry
Pump power
7.5 kW · 250 m³
Touch-off device
Yes
Travel speed X/Y
70 m/min
Travel speed Z
10 m/min
Working speed X/Y
20 m/min
Working speed Z
10 m/min
Total power
21 kW
Positioning cylinders
4 pcs
Dust outlet
Ø200 × 1
Overall size
4200 × 2300 × 2500 mm
Weight
2500 kg
ZORIDA RTS-4S CNC Router (Machining Centre) — catalogue photo, PDF p.4

CNC Router (Machining Centre)

RTS-4S

The four-spindle centre: four HQD 6 kW spindles ride the gantry together — the catalogue's inset shows all four heads — so repetitive cutting, grooving and drilling steps run in parallel instead of waiting for tool changes.

  • Four spindles working the same program in parallel
  • Total power 33 kW — the family's joint-highest
  • Suits high-volume nested production of identical part sets, where the same tools work every sheet
  • Weihong computer control, 7.5 kW Eurovac dry pump, touch-off device fitted
  • Family specification details and options are shown below the RTS cards (catalogue p.5)
Working size
1300 × 2800 × 50 mm
Spindle
HQD 6 kW × 4
ATC
Not fitted
Control system
Weihong computer
Servo system
Weihong
VFD
Fulling 7.5 kW
Vacuum pump
Eurovac dry
Pump power
7.5 kW · 250 m³
Touch-off device
Yes
Travel speed X/Y
70 m/min
Travel speed Z
10 m/min
Working speed X/Y
20 m/min
Working speed Z
10 m/min
Total power
33 kW
Positioning cylinders
4 pcs
Dust outlet
Ø200 × 1
Overall size
4200 × 2300 × 2500 mm
Weight
2500 kg
ZORIDA RTS-R8 CNC Router (Machining Centre) — catalogue photo, PDF p.4

CNC Router (Machining Centre)

RTS-R8

The disc-ATC centre: an 8-position rotary tool magazine — shown in the catalogue's inset — serves the HQD 9 kW spindle, giving fast tool changes in a compact head.

  • 8-position disc magazine for fast, compact tool changes
  • Specification otherwise matches the RTS-L12 (Weihong control, 11 kW VFD, 21 kW total, 2500 kg)
  • The choice between R8 and L12 is magazine style and tool count: eight tools on a disc, or twelve in a row
  • Family specification details and options are shown below the RTS cards (catalogue p.5)
Working size
1300 × 2800 × 50 mm
Spindle
HQD 9 kW
ATC
8 round ATC
Control system
Weihong computer
Servo system
Weihong
VFD
Fulling 11 kW
Vacuum pump
Eurovac dry
Pump power
7.5 kW · 250 m³
Touch-off device
Yes
Travel speed X/Y
70 m/min
Travel speed Z
10 m/min
Working speed X/Y
20 m/min
Working speed Z
10 m/min
Total power
21 kW
Positioning cylinders
4 pcs
Dust outlet
Ø200 × 1
Overall size
4200 × 2300 × 2500 mm
Weight
2500 kg

CNC router family — specification & options (catalogue p.5)

The catalogue’s specification page serves the whole RKS / RTS family: the standard equipment photographed here is shared by the family, and the four option photos are marked as options in the catalogue (the touch-off device is standard on the ATC models).

CNC router family — specification & options (catalogue p.5) — HQD spindle
HQD spindle
CNC router family — specification & options (catalogue p.5) — Positioning cylinder
Positioning cylinder
CNC router family — specification & options (catalogue p.5) — NCStudio servo motor
NCStudio servo motor
CNC router family — specification & options (catalogue p.5) — NCStudio computer control
NCStudio computer control
CNC router family — specification & options (catalogue p.5) — Handwheel
Handwheel
CNC router family — specification & options (catalogue p.5) — Touch-off device
Touch-off device
CNC router family — specification & options (catalogue p.5) — Option: HQD 5+4 vertical boring block
Option: HQD 5+4 vertical boring block
CNC router family — specification & options (catalogue p.5) — Option: double press rollers
Option: double press rollers
CNC router family — specification & options (catalogue p.5) — Option: 250 m³ Eurovac dry vacuum pump
Option: 250 m³ Eurovac dry vacuum pump
CNC router family — specification & options (catalogue p.5) — Option: rotation axis
Option: rotation axis

Series 02

Edge Banding Series

Twenty-six banders in the catalogue’s own order: the servo M series and our M7-288 flagship, the high-speed RFB865, then the specialists — wood & aluminium, profile, arc, L-shape and inclination models — the straight RFB465 / 565 and R-T families, and the narrow-panel and curved machines. Every card carries the model’s own catalogue photo, its own working-unit strip and its complete parameter table.

Watch it work: M7-288

Our flagship servo bander (card in the servo group below) running a full working cycle — gluing, pressing, trimming, scraping and buffing in one pass.

42-second Short — the M7-288 up close →

Ask for the M7-288 Price

Servo Control Edge Banders

ZORIDA RFB-M5 Servo Edge Bander — catalogue photo, PDF p.12
Working units — as shown in the catalogueRFB-M5 working units — catalogue diagram strip

Servo Edge Bander

RFB-M5

The first step of the servo ladder: the M5's beam lift is servo-driven, so panel thickness changeovers are set from the control instead of by hand.

  • Unit row: pre-milling, gluing, edge cutting, pressing, end trim, two fine trims, corner trim, two scraping units and buffing — see the unit strip under the photo
  • Feeds at 12–25 m/min on panels from a 180 × 38 mm minimum
  • Detail photos below show its pre-milling unit and double scraping unit
  • The M7 adds servo fine trim and servo scraping; the M9 adds servo pressing, pre-milling, end trim and corner trim on top
Edge band thickness
0.4–3 mm
Panel thickness
9–60 mm
Panel width
≥ 38 mm
Panel length
≥ 120 mm
Minimum panel size
180 × 38 mm
Feed speed
12–25 m/min
Voltage
380 V (±5%)
Working air pressure
0.65 kPa (as printed in the catalogue)
Total power
34 kW
Equipment weight
5800 kg
Overall dimension
10600 × 1000 × 1900 mm
Panel spacing
No rounding ≥ 600 mm · rounding ≥ 700 mm
ZORIDA RFB-M7 Servo Edge Bander — catalogue photo, PDF p.12
Working units — as shown in the catalogueRFB-M7 working units — catalogue diagram strip

Servo Edge Bander

RFB-M7

The M7 builds on the M5's servo beam lift with servo fine trimming and servo scraping, so the finishing units follow the panel profile automatically.

  • Servo fine trim and servo scraping are the step up from the M5; the beam lift servo is shared
  • Detail photos below: horizontal end trim, PUR glue station, servo fine trim, four-motor corner trim, servo scraping
  • Table values match the M5 — 12–25 m/min feed, 34 kW, 10600 mm body — so the step up buys servo control of the finish, not a bigger machine
  • For factories chasing a cleaner glue line and edge finish at volume
Edge band thickness
0.4–3 mm
Panel thickness
9–60 mm
Panel width
≥ 38 mm
Panel length
≥ 120 mm
Minimum panel size
180 × 38 mm
Feed speed
12–25 m/min
Voltage
380 V (±5%)
Working air pressure
0.65 kPa (as printed in the catalogue)
Total power
34 kW
Equipment weight
5800 kg
Overall dimension
10600 × 1000 × 1900 mm
Panel spacing
No rounding ≥ 600 mm · rounding ≥ 700 mm
ZORIDA RFB-M9 Servo Edge Bander — catalogue photo, PDF p.11
Working units — as shown in the catalogueRFB-M9 working units — catalogue diagram strip

Servo Edge Bander

RFB-M9

The top of the servo ladder: on top of the M7 it adds servo pressing, servo pre-milling, servo end trim and servo corner trim, with an 8-tape library feeding a V-belt conveyor.

  • Servo pressing, servo-driven end trim, servo trimming, servo rounding unit and servo scraping — all photographed below
  • 8-tape library (photo below): tape changes stop costing line time
  • The fastest of the three servo models at 15–28 m/min, and the smallest minimum panel: 120 × 50 mm
  • Built for high-mix door and cabinet plants that change over often
Edge band thickness
0.4–3 mm
Panel thickness
9–60 mm
Panel width
≥ 50 mm
Panel length
≥ 120 mm
Minimum panel size
120 × 50 mm
Feed speed
15–28 m/min
Voltage
380 V (±5%)
Working air pressure
0.65 kPa (as printed in the catalogue)
Total power
34 kW
Equipment weight
6000 kg
Overall dimension
7600 × 1130 × 2010 mm
Panel spacing
No rounding ≥ 600 mm · rounding ≥ 700 mm
ZORIDA M7-288 Full-Servo Edge Bander — workshop photo

Full-Servo Edge Bander

M7-288

Our flagship servo bander — and the machine running in the demo video at the top of this series. Its servo-controlled working units run the complete cycle in one pass.

  • Full cycle in one pass: gluing, pressing, end trimming, fine trimming, scraping and buffing
  • Feed speed up to 20 m/min
  • Built for cabinet, wardrobe and door factories that want a clean, sealed edge at production speed
  • Works MDF and particle board; watch the full working cycle in the video above, then ask us to configure it for your panels, tape and voltage
  • Not a catalogue model: it is our own production machine, photographed and filmed in the workshop — its full data sheet is supplied with your quotation
Control
Full servo
Feed speed
Up to 20 m/min
Cycle
Gluing · pressing · end trim · fine trim · scraping · buffing
Workpieces
MDF · particle board

Demonstrated in the video above; the full data sheet is supplied with your quotation.

High-Speed & Wood-Aluminium Edge Banders

ZORIDA RFB865 High-Speed Edge Bander — catalogue photo, PDF p.13
Working units — as shown in the catalogueRFB865 working units — catalogue diagram strip

High-Speed Edge Bander

RFB865

The high-speed model: the catalogue states its speed can reach 28 m/min, run by an industrial computer control system with a touch screen.

  • Two pre-melt gluing units and a double upper quick-melt keep glue supplied at pace
  • Double guide-rail end trim and four corner-trim motors keep up with the feed
  • The unit row doubles the finishing stations: rough trim, two fine trims, two scraping and two buffing units
  • V-belt conveyor carries panels smoothly (detail photos below)
  • A 10.5 m, 3600 kg machine for lines where banding is the bottleneck
Overall dimension
10500 × 1000 × 1700 mm
Total power
29 kW
Net weight
3600 kg
Working speed
20–23–26 m/min (28 m/min max.)
Panel thickness
10–60 mm
Panel width
≥ 60 mm
Panel length
≥ 120 mm
Edge band thickness
0.4–3 mm
ZORIDA RFB565JC-AH Wood & Aluminium Edge Bander — catalogue photo, PDF p.14
Working units — as shown in the catalogueRFB565JC-AH working units — catalogue diagram strip

Wood & Aluminium Edge Bander

RFB565JC-AH

The wood-and-aluminium model: the catalogue states it works for aluminium and wood panels alike — including the aluminium honeycomb panels in its detail photos.

  • End trim works after the trimming function — the sequence that aluminium work needs
  • PUR glue system and a long press system with two units of press rollers bond the tape
  • Four corner-trim motors with 0.37 kW × 4 independent high-frequency control
  • V-belt conveying and a 24″ computer control panel on a 9900 mm machine
  • For plants banding both timber panels and aluminium composite or honeycomb board
Overall dimension
9900 × 1000 × 1700 mm
Total power
16 kW
Net weight
3500 kg
Working speed
15–18–23 m/min
Panel thickness
9–60 mm
Panel width
≥ 50 mm
Panel length
≥ 120 mm
Edge band thickness
0.4–3 mm

Profile & Arc Edge Banders

ZORIDA RFB-770HC Profile Edge Bander — catalogue photo, PDF p.15
Working units — as shown in the catalogueRFB-770HC working units — catalogue diagram strip

Profile Edge Bander

RFB-770HC

The profile specialist: a forming press wraps tape onto shaped edges — J pulls, half-J and middle-J profiles, C shapes, bevels and straight edges — after pre-milling and twin forming milling stations shape the panel.

  • Carries the four devices the RFB-F50 leaves out: second milling, servo scraping, corner trim and an auto lift beam (photos below)
  • Tape widths are profile-specific: J 56 mm, C 35 mm, bevel & straight 28 mm on an 18 mm panel
  • Forming Press detail photo below
  • For handle-profile door production; 62.8 kW installed
Panel length
300 mm
Panel width
130 mm
Panel thickness
18 / 22 / 25 mm (one thickness as standard)
PVC tape thickness
Straight & bevel edge 0.6–1.5 mm · other shapes 0.5–0.8 mm
PVC tape width (on 18 mm panel)
J / half J / middle J: 56 mm · C: 35 mm · bevel & straight: 28 mm
Feed speed
8 m/min
Air pressure
0.6 MPa
Total power
62.8 kW
Machine dimensions (L×W×H)
9530 × 1000 × 1980 mm
ZORIDA RFB-F50 Profile Edge Bander — catalogue photo, PDF p.15
Working units — as shown in the catalogueRFB-F50 working units — catalogue diagram strip

Profile Edge Bander

RFB-F50

The RFB-770HC's platform mate without its four extra devices — and 57 kW instead of 62.8 kW.

  • No second milling, servo scraping, corner trim or auto lift beam — the four devices are listed on the catalogue page as the 770HC's additions
  • Keeps the forming press cycle: pre-milling, forming milling, edge band hogging for bevels, gluing, forming press, end trim, fine trimming, servo trimming, flat scraping and buffing
  • Same panel and tape table as the 770HC
  • The catalogue page gives this model no detail photos of its own — its photo and unit strip above are its own
  • Choose it when your profiles don't need the HC's extra finishing stations
Panel length
300 mm
Panel width
130 mm
Panel thickness
18 / 22 / 25 mm (one thickness as standard)
PVC tape thickness
Straight & bevel edge 0.6–1.5 mm · other shapes 0.5–0.8 mm
PVC tape width (on 18 mm panel)
J / half J / middle J: 56 mm · C: 35 mm · bevel & straight: 28 mm
Feed speed
8 m/min
Air pressure
0.6 MPa
Total power
57 kW
Machine dimensions (L×W×H)
9530 × 1000 × 1980 mm
ZORIDA RFB-F70 Arc Edge Bander — catalogue photo, PDF p.16
Working units — as shown in the catalogueRFB-F70 working units — catalogue diagram strip

Arc Edge Bander

RFB-F70

An arc-edge bander for shaped door and panel edges: J shape and C shape are standard, and you choose one further type from 1/4 arc, 1/2 arc, duckbill or 45° inclined straight.

  • Units: forming milling, gluing, edge band hogging for bevels, end trim, fine trimming, scraping, flat scraping and buffing
  • Runs at 8–10 m/min on 18 mm panels with 0.5–1 mm tape
  • All six profile samples from its catalogue page are in the gallery below
  • The RFB-F60 below chooses three profile types instead of one, and adds a forming press
Panel length
200 mm
Panel width
120 mm
Panel thickness
18 mm
Tape thickness
0.5–1 mm
Feed speed
8–10 m/min
Input voltage
380 V
Input frequency
50 Hz
Air pressure
0.6 MPa
Total power
20.8 kW
Machine dimensions (L×W×H)
6500 × 840 × 1980 mm
ZORIDA RFB-F60 Arc Edge Bander — catalogue photo, PDF p.16
Working units — as shown in the catalogueRFB-F60 working units — catalogue diagram strip

Arc Edge Bander

RFB-F60

The F70's sister machine with a wider profile choice: instead of one, you choose three types from 1/4 arc, 1/2 arc, duckbill and 45° inclined straight, and a forming press station joins the unit row.

  • Forming milling and forming press are photographed on its catalogue page (gallery below)
  • Every table value matches the F70 — 18 mm panels, 0.5–1 mm tape, 8–10 m/min, 20.8 kW
  • The choice between F70 and F60 is purely how many edge profiles you run
Panel length
200 mm
Panel width
120 mm
Panel thickness
18 mm
Tape thickness
0.5–1 mm
Feed speed
8–10 m/min
Input voltage
380 V
Input frequency
50 Hz
Air pressure
0.6 MPa
Total power
20.8 kW
Machine dimensions (L×W×H)
6500 × 840 × 1980 mm

L-Shape & Inclination Edge Banders

ZORIDA RFB-25L L-Shape Edge Bander — catalogue photo, PDF p.17
Working units — as shown in the catalogueRFB-25L working units — catalogue diagram strip

L-Shape Edge Bander

RFB-25L

The L-shape door specialist: double milling units and one trimming unit form and band the L profile machined into handle-less door panels, along with L-a and L-b edges, duckbill and 45° straight edges.

  • Tape thickness is specified per edge type: duckbill 0.6–0.8 mm, inclined & straight 0.8–1.0 mm, L-shaped 0.55–0.6 mm
  • Feeds at 8 m/min on 18–50 mm panels; 59.3 kW installed
  • Profile samples from its catalogue page are in the gallery below
  • The RFB-50L below is the faster, wider-ranging L model — compare the two tables
Panel length
200 mm
Panel width
140 mm
Panel thickness
18–50 mm
Sealing tape thickness
Duckbill 0.6–0.8 mm · inclined & straight 0.8–1.0 mm · L-shaped 0.55–0.6 mm
Feed speed
8 m/min
Input voltage
380 V
Input frequency
50 Hz
Air pressure
0.6 MPa
Total power
59.3 kW
Machine dimensions (L×W×H)
7850 × 900 × 1950 mm
ZORIDA RFB-50L L-Shape Edge Bander — catalogue photo, PDF p.17
Working units — as shown in the catalogueRFB-50L working units — catalogue diagram strip

L-Shape Edge Bander

RFB-50L

The faster, wider-ranging L-shape model: an L-shaped forming milling unit shapes the pull, then gluing and pressing, end trim, rough and fine trimming, scraping, flat scraping and buffing finish it.

  • Panels 10–60 mm thick with 0.3–3 mm tape — a far wider range than the 25L's 18–50 mm / profile-specific tapes
  • Feeds at 14–22 m/min, well beyond the 25L's 8 m/min
  • Detail photos below: rough and fine trim, and the L-shaped forming milling unit
  • Pick it when L-profile doors are a volume product, not an occasional one
Panel length
≥ 120 mm
Panel width
≥ 40 mm
Panel thickness
10–60 mm
Sealing tape thickness
0.3–3 mm
Feed speed
14–22 m/min
Input voltage
380 V
Input frequency
50 Hz
Air pressure
0.6 MPa
Total power
52.9 kW
Machine dimensions (L×W×H)
8830 × 1000 × 1950 mm
ZORIDA RFB-765JC Inclination (Bevel) Edge Bander — catalogue photo, PDF p.18
Working units — as shown in the catalogueRFB-765JC working units — catalogue diagram strip

Inclination (Bevel) Edge Bander

RFB-765JC

The full inclination machine: one button shifts it between bevelled and straight edges, with separate unit sets for each — the catalogue's finished-product photos show both edge types.

  • Bevel set: bevel cut, bevel edge gluing, pre-milling and fine trim for bevels
  • Straight set: straight-edge gluing, pre-milling, fine trim, corner trim and scraping — plus misting (melting) stations and twin buffing; 17 units in the strip under the photo
  • Detail photos below: its pre-milling unit and bevel saw blade
  • At 10 m long and 32.5 kW it is the complete bevel-and-straight station for mixed door production
Panel length
Inclined straight ≥ 250 mm · straight ≥ 120 mm
Panel width
Inclined straight ≥ 250 mm · straight ≥ 120 mm
Panel thickness
Inclined straight 15–25 mm · straight 9–50 mm · straight reserved > 5 mm
Edge band thickness
Inclined straight 0.6–1.5 mm · straight 0.4–3 mm
Infeed speed
0–22 m/min (5.5 kW feeding motor)
Lifting motor
0.37 kW
Air pressure
0.6 MPa
Total power
32.5 kW
Overall size
10000 × 950 × 1700 mm
Weight
3200 kg
ZORIDA RFB-765 Inclination (Bevel) Edge Bander — catalogue photo, PDF p.18
Working units — as shown in the catalogueRFB-765 working units — catalogue diagram strip

Inclination (Bevel) Edge Bander

RFB-765

The compact inclination model for bevel-led production, at roughly half the 765JC's footprint and power.

  • Unit row: bevel cut, edge band hogging, bevel edge gluing, end trim, fine trim for bevel, scraping and buffing
  • Works 15–25 mm panels with 0.6–1.5 mm tape at 0–22 m/min infeed
  • 7850 mm body at 16 kW — choose it when bevelled edges are the main job and straight-edge work is occasional
  • Note: the catalogue's shared table heads this model's column “RFB-745”; the values belong to this model, shown on the same page
Panel length
≥ 250 mm
Panel width
≥ 250 mm
Panel thickness
15–25 mm · straight reserved > 5 mm
Edge band thickness
0.6–1.5 mm
Infeed speed
0–22 m/min
Lifting motor
0.37 kW
Air pressure
0.6 MPa
Total power
16 kW
Overall size
7850 × 1000 × 1700 mm
Weight
Not stated in the catalogue

Straight Automatic Edge Banders — RFB465 / 565 Family

ZORIDA RFB465 Automatic Edge Bander — catalogue photo, PDF p.19
Working units — as shown in the catalogueRFB465 working units — catalogue diagram strip

Automatic Edge Bander

RFB465

The starting model of the RFB465 / 565 family — and already a full-speed one: 15–18–23 m/min on panels 10–60 mm thick with 0.4–3 mm tape.

  • Unit row: gluing, edge cutting, pressing, end trim, fine trimming, scraping and buffing (strip under the photo)
  • No pre-milling and no rough trim — the steps up are the 465J (pre-milling) and the 565 (rough trim)
  • Family specification: multi tape feed system, narrow-panel processing, guide rail for hinge holes, scraping tape cut
  • Family options: hogging, crawler-type beam, spray station, PUR glue machine, quick melt — the family page is shown below this family's cards
  • The practical entry point into the RFB range
Overall dimension
4100 × 850 × 1680 mm
Total power
8 kW
Net weight
1450 kg
Working speed
15–18–23 m/min
Panel thickness
10–60 mm
Panel width
≥ 60 mm
Panel length
≥ 120 mm
Edge band thickness
0.4–3 mm
ZORIDA RFB465J Automatic Edge Bander — catalogue photo, PDF p.19
Working units — as shown in the catalogueRFB465J working units — catalogue diagram strip

Automatic Edge Bander

RFB465J

The extended RFB465: a longer 4600 mm body, 13 kW installed, and pre-milling added ahead of the gluing station, so panels are trued up before the tape goes on.

  • The J step over the 465 is pre-milling plus the longer, heavier body
  • Speed, panel range and tape range match the family: up to 23 m/min, 10–60 mm panels, 0.4–3 mm tape
  • Shares the family specification and options, including PUR glue and quick melt (family page below)
  • Pick it over the RFB465 when pre-milling and a longer machine fit your panels and daily volume
Overall dimension
4600 × 850 × 1680 mm
Total power
13 kW
Net weight
1650 kg
Working speed
15–18–23 m/min
Panel thickness
10–60 mm
Panel width
≥ 60 mm
Panel length
≥ 120 mm
Edge band thickness
0.4–3 mm
ZORIDA RFB565 Automatic Edge Bander — catalogue photo, PDF p.19
Working units — as shown in the catalogueRFB565 working units — catalogue diagram strip

Automatic Edge Bander

RFB565

The 565 step of the family adds a rough trimming unit to the cycle, for panels that need heavier stock removal before the fine pass.

  • Unit row: gluing, edge cutting, pressing, end trim, rough trim, fine trim, scraping and buffing
  • Against the 465J it trades pre-milling for rough trimming — check which your panels need
  • 4600 mm body at the family speed of up to 23 m/min across the full 10–60 mm thickness range
  • Multi tape feed, narrow-panel processing, hinge-hole guide rail and scraping tape cut come from the shared family specification
Overall dimension
4600 × 850 × 1680 mm
Total power
10 kW
Net weight
1650 kg
Working speed
15–18–23 m/min
Panel thickness
10–60 mm
Panel width
≥ 60 mm
Panel length
≥ 120 mm
Edge band thickness
0.4–3 mm
ZORIDA RFB565J Automatic Edge Bander — catalogue photo, PDF p.19
Working units — as shown in the catalogueRFB565J working units — catalogue diagram strip

Automatic Edge Bander

RFB565J

The long-body RFB565: at 5450 mm it gives its nine working units more room, and the panel a longer, steadier run through the machine.

  • Nine units: pre-milling through rough and fine trimming to scraping and buffing
  • Installed power 14.2 kW, weight 2080 kg
  • Family speed and ranges unchanged: 15–18–23 m/min, 10–60 mm panels
  • Choose the J when longer panels or a heavier daily schedule make the standard 565 body feel tight
Overall dimension
5450 × 1000 × 1600 mm
Total power
14.2 kW
Net weight
2080 kg
Working speed
15–18–23 m/min
Panel thickness
10–60 mm
Panel width
≥ 60 mm
Panel length
≥ 120 mm
Edge band thickness
0.4–3 mm
ZORIDA RFB565JC Automatic Edge Bander — catalogue photo, PDF p.19
Working units — as shown in the catalogueRFB565JC working units — catalogue diagram strip

Automatic Edge Bander

RFB565JC

The flagship of the RFB465 / 565 family: the longest body in the range at 6640 mm and the fullest unit row, adding corner trimming.

  • Unit row: pre-milling, gluing, edge cutting, pressing, end trim, rough and fine trimming, corner trim, scraping and buffing
  • Speed, thickness and tape range match the family: up to 23 m/min, 10–60 mm panels, 0.4–3 mm tape
  • Family options (PUR glue machine, quick melt, hogging, crawler-type beam, spray station) are all available
  • For factories that want one bander to finish panels completely
Overall dimension
6640 × 1000 × 1600 mm
Total power
17 kW
Net weight
2280 kg
Working speed
15–18–23 m/min
Panel thickness
10–60 mm
Panel width
≥ 60 mm
Panel length
≥ 120 mm
Edge band thickness
0.4–3 mm

RFB465 / 565 family — unit details & options (catalogue p.20)

The family specification page: the six working units photographed for the whole family, the family’s extra features — soft flat scraping (M), scraping tape cut (S), guide roller for hinge holes (G), PUR glue machine and quick melt — and its three options. The family description also lists the multi tape feed system (M), narrow-panel processing (N), the hinge-hole guide rail (G) and scraping tape cut (S).

RFB465 / 565 family — unit details & options (catalogue p.20) — Pre-milling
Pre-milling
RFB465 / 565 family — unit details & options (catalogue p.20) — End trim
End trim
RFB465 / 565 family — unit details & options (catalogue p.20) — Rough and fine trim
Rough and fine trim
RFB465 / 565 family — unit details & options (catalogue p.20) — Corner trim
Corner trim
RFB465 / 565 family — unit details & options (catalogue p.20) — Scraping
Scraping
RFB465 / 565 family — unit details & options (catalogue p.20) — Buffing
Buffing
RFB465 / 565 family — unit details & options (catalogue p.20) — Soft flat scraping
Soft flat scraping
RFB465 / 565 family — unit details & options (catalogue p.20) — Scraping tape cut
Scraping tape cut
RFB465 / 565 family — unit details & options (catalogue p.20) — Guide roller for hinge holes
Guide roller for hinge holes
RFB465 / 565 family — unit details & options (catalogue p.20) — PUR glue machine
PUR glue machine
RFB465 / 565 family — unit details & options (catalogue p.20) — Quick melt
Quick melt
RFB465 / 565 family — unit details & options (catalogue p.20) — Option: hogging
Option: hogging
RFB465 / 565 family — unit details & options (catalogue p.20) — Option: crawler-type pressure beam
Option: crawler-type pressure beam
RFB465 / 565 family — unit details & options (catalogue p.20) — Option: spray station
Option: spray station

Straight Automatic Edge Banders — R-T Family

ZORIDA R-T2 Automatic Edge Bander — catalogue photo, PDF p.22
Working units — as shown in the catalogueR-T2 working units — catalogue diagram strip

Automatic Edge Bander

R-T2

The entry model of the R-T family: a compact through-feed bander that runs gluing, end trim, fine trim, scraping and buffing in one pass.

  • Detail photos on its catalogue spread show the details that matter at this price: an encoder tape counter, Teflon-coated glue application, pre-milling amount display, movable 10″ control panel, clean / spray station and glue scrapers on the press rollers
  • Options on the same spread: narrow-panel support (over 40 mm), CE specification, electrical lift beam
  • The R-T3 adds pre-milling; the R-T4 adds pre-milling and corner trim — compare the three tables
  • A sound first automatic bander for small and mid-size cabinet workshops
Min. panel length
120 mm
Min. panel width
80 mm
Panel thickness
10–40 mm
Edge band thickness
0.4–2 mm
Feed speed
10 m/min
Air pressure
0.6–0.8 MPa
Pre-milling
Not fitted
Gluing power
0.55 kW
End trim power
0.37 kW × 2
Fine trim power
0.55 kW × 2
Corner trim power
Not fitted
Buffing power
0.37 kW × 2
Feed power
1.5 kW
Heating plate power
1.5 kW
Total power
8 kW
Package size
3450 × 750 × 1240 mm
ZORIDA R-T3 Automatic Edge Bander — catalogue photo, PDF p.22
Working units — as shown in the catalogueR-T3 working units — catalogue diagram strip

Automatic Edge Bander

R-T3

The middle model of the R-T family adds the unit the R-T2 leaves out: twin 2.2 kW pre-milling motors that true up the panel edge before gluing, so the glue line stays thin and even on sawn MDF and particle board.

  • Pre-milling is the step up from the R-T2 — the rest of the cycle (gluing, end trim, fine trim, scraping, buffing) matches the family
  • Installed power rises to 11.5 kW against the R-T2's 9.6 kW
  • The catalogue spread's detail photos belong to the R-T2's presentation, so this card carries the R-T3's own photo and unit strip only
  • Choose it when your panels arrive from the saw with edges that need correcting before banding
Min. panel length
120 mm
Min. panel width
80 mm
Panel thickness
10–40 mm
Edge band thickness
0.4–2 mm
Feed speed
10 m/min
Air pressure
0.6–0.8 MPa
Pre-milling
2.2 kW × 2
Gluing power
0.55 kW
End trim power
0.37 kW × 2
Fine trim power
0.55 kW × 2
Corner trim power
Not fitted
Buffing power
0.37 kW × 2
Feed power
1.5 kW
Heating plate power
1.5 kW
Total power
11.5 kW
Package size
4000 × 750 × 1240 mm
ZORIDA R-T4 Automatic Edge Bander — catalogue photo, PDF p.21
Working units — as shown in the catalogueR-T4 working units — catalogue diagram strip

Automatic Edge Bander

R-T4

The top model of the R-T family and the only one with corner trimming: panels leave the bander finished, corners included.

  • Full cycle: pre-milling, gluing and pressing, end trim, fine trim, corner trim, scraping, soft flat scraping and buffing
  • Feed speed steps up to 12 / 15 / 18 m/min with a 2.2 kW feed motor
  • Detail photos below show its 2.2 kW pre-milling unit and corner trim station up close
  • For factories that want cabinet and door panels finished in a single pass
Min. panel length
120 mm
Min. panel width
80 mm
Panel thickness
10–40 mm
Edge band thickness
0.4–2 mm
Feed speed
12 / 15 / 18 m/min
Air pressure
0.6–0.8 MPa
Pre-milling
2.2 kW × 2
Gluing power
0.55 kW
End trim power
0.37 kW × 2
Fine trim power
0.55 kW × 2
Corner trim power
0.37 kW × 2
Buffing power
0.37 kW × 2
Feed power
2.2 kW
Heating plate power
1.5 kW
Total power
12.5 kW
Package size
5370 × 750 × 1240 mm

Narrow-Panel & Curved Edge Banders

ZORIDA RFB-28S Narrow Panel Edge Bander — catalogue photo, PDF p.23
Working units — as shown in the catalogueRFB-28S working units — catalogue diagram strip

Narrow Panel Edge Bander

RFB-28S

The narrow-panel specialist: it bands strips down to 28 mm wide — the catalogue calls out a 28 mm panel in its detail photo — that standard banders cannot hold.

  • Pressure beam with automatic lifting, a dedicated narrow-panel support device and small-roller conveying keep slim parts stable
  • Full cycle: gluing, edge cutting, pressing, end trim, rough and fine trimming, scraping and buffing
  • Still runs at 15–18–20 m/min on panels up to 60 mm thick
  • For drawer sides, slats and slim frame parts
Overall dimension
4600 × 1000 × 1700 mm
Total power
23 kW
Net weight
3200 kg
Working speed
15–18–20 m/min
Panel thickness
10–60 mm
Panel width
≥ 28 mm
Panel length
≥ 120 mm
Edge band thickness
0.4–3 mm
ZORIDA RFB-D330 CNC Curved Edge Bander — catalogue photo, PDF p.23

CNC Curved Edge Bander

RFB-D330

A CNC curved bander for parts that are not straight at all: the catalogue's shape icons show round, arc and square workpieces, held on a vacuum panel holder while the glue shaft and scraping unit follow the contour.

  • Suits shaped table tops, rounded cabinet parts and one-off curved work that no through-feed machine can take
  • Detail photos below: glue shaft, vacuum panel holder and scraping unit
  • The catalogue presents this model by its working photos rather than a parameter table — tell us your shapes and sizes and we will confirm the configuration in the quotation

The catalogue shows this model's glue shaft, vacuum panel holder and scraping unit in detail; its full specification is confirmed with your quotation.

ZORIDA RFB315B Curved Edge Bander (Benchtop) — catalogue photo, PDF p.23

Curved Edge Bander (Benchtop)

RFB315B

A compact benchtop curved bander: the workpiece is guided by hand around the pin-covered table while the machine glues and applies the tape, with a foot pedal controlling the cycle — visible in the catalogue photo.

  • The workshop-scale answer for curved and irregular edges on individual pieces, samples and short runs
  • The catalogue presents it by photo only, with no parameter table and no unit strip
  • Ask us for its working range against your parts when you enquire

Presented by photo in the catalogue; full specification is supplied with your quotation.

ZORIDA RFB315Q Curved Edge Bander — catalogue photo, PDF p.23

Curved Edge Bander

RFB315Q

The second curved bander on the catalogue's final page, shown with its own raised control panel above the pin table.

  • Built, like the 315B, for hand-guided curved and shaped edges in small workshops and for odd-shaped parts in a larger plant
  • The catalogue shows it by photo only, alongside the 315B — no parameter table is published for either
  • Send us your part shapes and we will confirm which of the two fits, and quote it in full

Presented by photo in the catalogue; full specification is supplied with your quotation.

Series 03

Six-Sided Drilling & Drilling Series

Six RMZ six-sided drills — from the single-pack 126A to the two-board 166EC — plus the machines that finish the details: the RMZ-S1 dowel & embedded-handle machine, the RDG-2800S tenoner and mortiser, and the RDG handle drilling machines for handle-less doors.

Watch it work: six-sided drilling

Real workshop footage of a ZORIDA six-sided drill cycling panels — top and bottom drilling in a single pass. The full-length drilling demonstration is on our YouTube channel.

ZORIDA Machinery on YouTube →

Ask About Six-Sided Drills

CNC Six-Sided Drilling Machines — RMZ Series

ZORIDA RMZ126A CNC Six-Sided Drilling Machine — catalogue photo, PDF p.6

CNC Six-Sided Drilling Machine

RMZ126A

The base six-sided drill: one upper drill pack (layout A in the catalogue's diagrams) plus a bottom drill block complete every face of the panel in a single pass-through cycle, at 80–100 pieces per hour.

  • One upper drill pack: 12 vertical drills plus X 2×2 + Y 2×2 horizontal drills
  • Bottom drill block with 10 vertical drills finishes the underside in the same pass
  • Twin 3.5 kW main shafts; boards 9–40 mm thick
  • Detail photos below show its spindle, twin clampers, bottom drill block, side-roller positioning, fan and belt conveyor
  • Options: saw blade unit, rear air table, return roller conveyor (photos below)
Efficiency
80–100 pcs / hour
Main shaft power
3.5 kW × 2 pcs
Upper vertical drill
12 pcs
Upper horizontal drill
X: 2×2 + Y: 2×2
Bottom vertical drill
10 pcs
Board thickness
9–40 mm
ZORIDA RMZ126B CNC Six-Sided Drilling Machine — catalogue photo, PDF p.6

CNC Six-Sided Drilling Machine

RMZ126B

The twin-pack version: layout B doubles the upper drill units, so denser hole patterns complete in the same single pass.

  • Two upper drill units: 12 vertical drills in each, with (X 2×2 + Y 2×1) × 2 horizontal drills
  • Bottom drill block unchanged: 10 vertical drills
  • Efficiency, main shaft power and board range match the 126A — 80–100 pcs/hour, 3.5 kW × 2, 9–40 mm boards
  • What doubles is the drilling hardware above the panel — choose it for heavy hinge, shelf and connector hole counts
  • The same options as the 126A (saw blade unit, rear air table, return roller conveyor) are offered
Efficiency
80–100 pcs / hour
Main shaft power
3.5 kW × 2 pcs
Upper vertical drill
12 × 2 units
Upper horizontal drill
(X: 2×2 + Y: 2×1) × 2
Bottom vertical drill
10 pcs
Board thickness
9–40 mm
ZORIDA RMZ126B-T CNC Six-Sided Drilling Machine — catalogue photo, PDF p.7

CNC Six-Sided Drilling Machine

RMZ126B-T

The T generation: two top drill units and one bottom unit, plus a 6 kW top spindle for routing and grooving work — the page's sample photos show lamello-style slots, hinge cups and handle grooves.

  • The catalogue also lists a 126A-T variant with one top and one bottom drill unit
  • 6 kW top spindle and 3.5 kW bottom spindle, 18000 rpm, for grooving and profiling as well as drilling
  • Side-roller positioning and a touch-off device are shown in the detail photos
  • 8-position ATC tool holder with cutters is an option (photo below)
  • Boards 200–2800 mm long, 50–1200 mm wide, 9–40 mm thick; axis speeds up to 100 / 65 / 20 m/min
  • Eleven machining samples from its catalogue page are in the gallery below
Board length
200–2800 mm
Board width
50–1200 mm
Board thickness
9–40 mm
Max. axis speed X/Y/Z
100 / 65 / 20 m/min
Top spindle
6 kW
Bottom spindle
3.5 kW
Air blower fan
2.2 kW
Spindle speed
18000 rpm
Upper vertical drill
12 × 12
Upper horizontal drill
X: 8 + Y: 6
Bottom vertical drill
9 pcs
ZORIDA RMZ-126AE CNC Six-Sided Drilling Machine — catalogue photo, PDF p.8

CNC Six-Sided Drilling Machine

RMZ-126AE

The enclosed-cabinet generation: the working area sits behind a full-width viewing window and axis speeds rise to 120 / 80 / 30 m/min. The AE is the single-top-pack version.

  • Layout AE (diagram below): 12 upper vertical drills, X4 + Y4 upper horizontal drills
  • 9 bottom vertical drills and twin 3.5 kW main shafts; 80–100 pieces per hour
  • Enclosed cabinet with full-width viewing window
  • Pick the AE for standard hole patterns; the BE below doubles the top pack for dense ones
Board length
200–2800 mm
Board width
50–1200 mm
Board thickness
9–40 mm
Max. axis speed X/Y/Z
120 / 80 / 30 m/min
Main shaft power
3.5 kW × 2 pcs
Spindle speed
18000 rpm
Upper vertical drill
12 pcs
Upper horizontal drill
X: 4 + Y: 4
Bottom vertical drill
9 pcs
Work efficiency
80–100 pcs / hour
ZORIDA RMZ-126BE CNC Six-Sided Drilling Machine — catalogue photo, PDF p.8

CNC Six-Sided Drilling Machine

RMZ-126BE

The twin-pack enclosed model: diagram BE doubles the top drilling hardware of the AE, while board range, axis speeds and the bottom drill stay the same.

  • Layout BE (diagram below): 12 × 2 upper vertical drills, (X4 + Y2) × 2 upper horizontal drills
  • 9 bottom vertical drills, twin 3.5 kW main shafts, 80–100 pieces per hour
  • The extra pack is spent on pattern density rather than pace
  • Enclosed cabinet with full-width viewing window, as on the AE
Board length
200–2800 mm
Board width
50–1200 mm
Board thickness
9–40 mm
Max. axis speed X/Y/Z
120 / 80 / 30 m/min
Main shaft power
3.5 kW × 2 pcs
Spindle speed
18000 rpm
Upper vertical drill
12 × 2
Upper horizontal drill
(X: 4 + Y: 2) × 2
Bottom vertical drill
9 pcs
Work efficiency
80–100 pcs / hour
ZORIDA RMZ-166EC CNC Six-Sided Drilling Machine — catalogue photo, PDF p.8

CNC Six-Sided Drilling Machine

RMZ-166EC

The wide flagship of the drilling range: it processes two boards side by side, with ball-screw transmission on its moving units — the catalogue shows the ball-screw detail under this model.

  • Two boards per pass across the 50–800 mm width range — 80–100 pcs/hour, but every pass carries twice the work
  • Four 3.5 kW spindles, doubled top drill sets and two groups of bottom drills
  • Ball-screw transmission, photographed and diagrammed below
  • 30 kW total on a 6300 × 3380 × 2150 mm frame (16.25 m² footprint)
Efficiency
80–100 pcs / hour
Panel length
200–2800 mm
Panel width
50–800 mm (2 boards processed)
Panel thickness
9–40 mm
Max. axis speed X/Y/Z
120 / 80 / 30 m/min
High-pressure blower
2.2 kW × 2
Spindle power
3.5 kW × 4
Spindle speed
18000 rpm
Top vertical drill
12 × 12 pcs
Top horizontal drill
X: 2×2×2 + Y: 2×2×2
Bottom vertical drill
9 pcs × 2 groups
Total power
30 kW
Size (L×W×H)
6300 × 3380 × 2150 mm · footprint 16.25 m²

Handle, Tenon & Mortise Drilling — RMZ-S1 & RDG Series

ZORIDA RMZ-S1 Embedded Handle & Dowel Drilling Machine — catalogue photo, PDF p.9

Embedded Handle & Dowel Drilling Machine

RMZ-S1

A drilling machine that also sets the dowels: drill spindle, dowel insert unit and automatic dowel holder work as one workflow, at 60 inserts per minute.

  • Drills and pins in one station — factories fitting embedded handles and dowel joints get both operations from one machine
  • X axis travels 2440 mm at 40 m/min; drilling to 50 mm deep, pinning to 40 mm
  • The catalogue's detail photos show the dowel insert, drill spindle and dowel holder at work
Spindle power
1.5 kW
Spindle speed
0–24000 r/min
X axis
40 m/min · 2440 mm travel
Y axis
40 m/min · 80 mm travel
Z axis
10 m/min · 50 mm travel
Punching speed
60 inserts / min
Max. drilling depth
50 mm
Max. pin depth
40 mm
Weight
1780 kg
Overall dimension
3462 × 1133 × 2015 mm
ZORIDA RDG-2800S Tenoner and Mortiser — catalogue photo, PDF p.9
Tenon & mortise joint profilesRDG-2800S working units — catalogue diagram strip

Tenoner and Mortiser

RDG-2800S

A tenon and mortise machine with high-speed four-spindle machining: the spindle set mixes one 2.2 kW, two 3.5 kW and one 6 kW unit, so the catalogue's full joint range runs in one setup.

  • Joint profiles (panel below): elongated tenons and 45° slots, mitred cross-lap joints, Chinese three-way mitred joints, haunched tenons, oval mortise-and-tenon, door and window tenons
  • Pneumatic material pressing and a cylinder lifting fence hold the work
  • Double work zones keep one side loading while the other cuts
  • 2800 mm stroke
X/Y/Z axis stroke
2800 / 150 / 70 mm
Drive motor power
750 W × 3 servo motors
Spindle motor power
2.2 kW × 1 · 3.5 kW × 2 · 6 kW × 1
Frequency converter
7.5 kW
Work table stroke
2800 mm
Overall size
4000 × 1500 × 1500 mm
ZORIDA RDG-H3-5T Embedded Handle Drilling Machine — catalogue photo, PDF p.10
Handle profiles machined by this machineRDG-H3-5T working units — catalogue diagram strip

Embedded Handle Drilling Machine

RDG-H3-5T

A CNC handle drilling machine with high-speed three-spindle machining and a 5-position ATC — the specialist for handle-less doors, where the pull is machined into the door itself.

  • Profile panel below: cove corners, hinge holes, semi-pass pulls, rectangular pulls, rocket pulls, straighten braces, U-shaped pulls and hinge screw holes
  • PLC numerical control screen and touch-off device, shown in the detail photos
  • 5-position ATC for the three-spindle set
  • Step up to the RDG-H5-6T below for five spindles, a longer stroke and arc / lamello profiles
X/Y/Z axis stroke
2800 / 120 / 70 mm
Servo motor set
750 W × 3 servo motors
High-speed spindles
2 × 3.5 kW / 1 × 6 kW
Frequency converter
7.5 kW
Table surface size
3200 × 500 mm
Overall size
4600 × 1600 × 1500 mm
Weight
1000 kg
ZORIDA RDG-H5-6T Embedded Handle Drilling Machine — catalogue photo, PDF p.10
Handle profiles machined by this machineRDG-H5-6T working units — catalogue diagram strip

Embedded Handle Drilling Machine

RDG-H5-6T

The five-spindle step up in handle drilling: high-speed five-spindle machining, a strengthened pressing mechanism and a movable cylinder locking crossbeam to hold long doors steady.

  • Profile panel below adds arc pulls, 45° lamello joints and door slots to the H3-5T's range
  • ATC-type 6 kW spindle in the five-spindle set
  • X stroke grows to 3050 mm against the H3-5T
  • Choose it when handle machining is a full-time station rather than a side operation
X/Y/Z axis stroke
3050 / 120 / 70 mm
Servo motor set
1500 W × 2 · 750 W × 1
High-speed spindles
6 kW + 3.5 kW × 3 + 6 kW ATC type
Frequency converter
7.5 kW
Overall size
4900 × 1400 × 1300 mm

Line Solutions

Complete production lines, planned as one line

A panel furniture line only runs as fast as its slowest handover. We plan cutting, banding and drilling together — machine widths, feed speeds and panel flow matched — and supply the whole line from one source. The RTS-12L nesting line below is the catalogue's own line layout: lift-table loading, vacuum placement, pusher registration and belt outfeed.

1 · CuttingRCJ beam saw or nesting line breaks sheets into parts
2 · LabellingParts labelled at the saw / nesting station
3 · Edge BandingStraight, profile or bevel banding to finish
4 · DrillingSix-sided drilling completes every face in one pass
5 · AssemblyParts arrive at assembly drilled, banded and labelled
ZORIDA RTS-12L CNC nesting line with load lift table, vacuum loading, pusher and belt output conveyor, from the ZORIDA catalogue

Service & Support

From first message to a running line

1 · Consult & Configure

Tell us your panels, products and daily output. We recommend the model and configuration that fit — and say so when a smaller machine is enough.

2 · Test-Run Before Shipment

Your machine is run and checked before it ships. We send you the test-run video, so you see your own machine working before it leaves.

3 · Export Packing & Loading

Seaworthy export packing and supervised container loading from Foshan, with loading photos shared with you.

4 · Setup & After-Sales

Manuals in English, and setup and operation guidance by WhatsApp video call. Spare parts and technical support stay one message away.

About ZORIDA

Based in Shunde, Foshan — China's furniture machinery base

Foshan Zorida Machinery Equipment Co., Ltd. (佛山市锆锐达机械设备有限公司) is a panel furniture equipment and solution specialist. We work with furniture factories, cabinet and wardrobe makers and door producers — recommending the right machine for the product, not the biggest one on the list — and we export worldwide. Follow the machines at work on YouTube (@ZoridaMachinery) and Instagram, including the six-sided drilling Short filmed in a real workshop.

A ZORIDA machine on its pre-shipment test run in the workshop
Pre-shipment test run — every machine works before it leaves.
Machine assembly in progress in the workshop
Assembly in the workshop.

Get a Quotation

Tell us what you produce

Fill in the form and it opens WhatsApp with your enquiry ready to send — no account, no waiting for an email reply. The more you tell us about your panels and output, the more exact the quotation.

Submitting opens WhatsApp with your details pre-filled, addressed to ZORIDA on +86 135 3459 1902. Nothing is sent until you press send in WhatsApp.

FAQ

Questions buyers ask us

Can the machines run on my country's voltage?

Yes. Tell us your voltage and frequency when you enquire — for example 415 V / 50 Hz or 220 V / 60 Hz — and the machine is configured for it before shipment. Voltage is confirmed in writing in your quotation.

How long until my machine ships?

Lead time depends on the model and configuration. Your quotation states the production and delivery schedule in writing, and we share test-run and loading photos and video as your order progresses.

Can I see my machine working before it ships?

Yes. Every machine is test-run before shipment and we send you the test-run video of your own machine. You are also welcome to inspect in person, or appoint an inspector — customers do both.

Do you sell single machines or only complete lines?

Both. Many customers start with one edge bander or one six-sided drill and add machines as they grow. If you are planning a new factory, we will lay out the whole line — cutting, banding, drilling — as one plan.

How do I install and learn the machine after it arrives?

Machines ship with English manuals. We guide your team through setup and first runs by WhatsApp video call, and stay available for operation and maintenance questions afterwards.

Which countries do you export to?

We export worldwide from Foshan, China. Send us your destination port in the enquiry and the quotation will include the machine configured for your market.

WhatsApp Us